Carsoft Success!

[David Mc]

Finally, after 3 months of experimenting, copying and deleting files, computer harddrive purging and reprogramming I have succeeded in making Carsoft 6.5 SP1 work with my E36!

I can now conduct diagnostics and read live data and have access to all of those nice little extras like door lock programming etc..

[en5]

Are you using the OBDII under the dash or the 20 pin circle port under the hood? Also, which cable bundle did you go with?

[w1ggy2002]

Nice one David,
But can you please tell us all how you did it eventually. I have tried for weeks and can only manage live data using obdII and 20 pin. Pc crashes on any other scan ????? And I have tried this on various Models of BMW.
Cheers

[David Mc]

I am using the 20 pin diagnostic port under the hood as my vehicle does not have an OBDII port. I purchased my interface, which is marked "BMW compatible interface V6.5" and has LED's for Power, Service Interval, K-Line Pin 20, K-Line Pin 17 and L-Line Pin 15 off E-Bay.

I purchased Carsoft 6.5 from a vendor in the UK off EBay and downloaded SP1 direct from the Carsoft Web site. PM me for full instructions.

[BJO]

Does your Carsoft read E36 ABS codes? Mine does not and I have never been able to get it to work.

[w1ggy2002]

David, Could you post instuctions on here as I cant seem to PM you. I tried to install the SP1 from Carsoft website but after installation would not let me open carsoft, came up with error.... Where am I going wrong ????

[David Mc]

To successfully install SP1 you must do it immediately after installing the Carsoft program (i.e. before Crack Installation). You will need to completely uninstall the whole program first.

The notes I used are attached below and are long and some may think a bit tedious - but the program does work! My Carsoft will read the following modules on my E36:- DME/DDE, Instrument Cluster, Airbag, ZKE/ZVM, EGS and EWS. Since I don't have an alarm system, rain or light sensors I think that is the full compliment. Notes are as follows:-

CARSOFT BMW 6.5 + SP1 INSTALLATION INSTRUCTIONS – WINDOWS XP

The procedure EXACTLY for Windows XP is as follows:-

If you have EVER installed ANY version of Carsoft before:-

1. Uninstal the program using the ADD/DELETE Programs function available from the Control panel via SETTINGS on the START menu.

2. Use the Explore function to open the Programs tab from the START menu and delete any CARSOFT folders

3. Use the SEARCH function from the START menu to look for any files or folders containing the word CARSOFT and delete them.

4. Search your Hard Drive for a folder named CM70 or CM75s and use EXPLORE to view its contents. If you have located the correct folder it will contain CARSOFT files with names like "AIRBAG1.DXT" - DELETE THE ENTIRE FOLDER.

5. Restart your computer and from the START menu go to PROGRAMS then ACCESSORIES and select SYSTEM TOOLS then SYSTEM RESTORE and create a new restore point.

6. Once the new restore point has been created, close out of the SYSTEM RESTORE Menu, then go back into ACCESSORIES via the START and PROGRAMS Menus and choose SYSTEM TOOLS then DISK CLEANUP. Select the MORE OPTIONS Tab and under “System Restore,” choose to Delete all but the most recent RESTORE Point and run the Disk Cleanup utility.

7. Open the “My Computer” Icon on the Desktop and right click on the Icon for your Hard Drive, then click “Properties”. Click on the “Tools” Tab when the Properties Dialogue Box opens and choose “Check now”. Two Dialogue boxes will appear asking if you want to check & repair files and scan the hard drive. Check both boxes then the START button. A message will appear telling you that this process can only be performed when the computer re-starts and asking you to confirm whether you wish this to occur. Confirm this request, then restart your computer. Dependent upon how many files you have stored and the size of the Hard Drive, the scanning process may take 2 -3 hours to complete after the system is restarted.

8. Temporarily disable any Anti-Virus or Spyware Programs that may be Running and use the setup program provided with the CARSOFT software to install CARSOFT 6.5.

9. Install SP1 which will search out and install to the CARSOFT/BMW Folder that has been copied to your hard drive.

10. Open the CRACKS Folder and copy ALL of the files contained in the Folder (including Instructions) to the BMW folder located in the newly created CARSOFT program Folder on your Hard Drive. The easiest way to accomplish this is firstly to open the CRACKS Folder then left click on the first file it contains and then each subsequent file whilst holding down the SHIFT key until ALL of the files are highlighted, then choose COPY THESE FILES and when the Dialogue Box pops up, locate the BMW folder in the newly installed CARSOFT folder on your Hard Drive, left click on it and then click on the COPY button.

11. Once this process has been completed, use the EXPLORE function to view the files in the BMW Folder of the newly installed CARSOFT Program. There will be 2 files with 6.5 Icons, labelled CARSOFT and CARSOFTBMW65. Delete the CARSOFT file and re-name CARSOFTBMW65 as CARSOFT.

12. Empty the deleted items from your trash bin and restart the system – CARSOFT 6.5.06 is now installed.

Remember to disable any anit-virus or Spyware programs prior to running the program

[w1ggy2002]

Thanks ever so much for this info. I will give it a go and let you know the outcome.
Been at this for over 2 months now...

[a32guy]

Wow thats sweet. Was this on an OBD1 or OBD2 car?

[David Mc]

The car has a build date of December 1997 (1998 model year) but does not have a 16 pin OBDII port. Diagnostics are performed using the round 20 pin port under the hood.

[w1ggy2002]

David, Just to let you know that the info you gave is 100% good, got it up and running and works like a charm on my motor, cant thank you enough.
No more head scratching
Cheers

[David Mc]

Glad to hear it worked for you too. Believe me when I say that I know how frustrating it can be. Happy motoring.

[TheM3nsah]

thnk you for this information!

[SIDNIK223]

thnk you for this information!

+1 for the info

[Teetr]

Thankyou for this step-by-step instruction
. I got my interface working now with no problems.

[JETninja]

Hmm, first time in this Forum, Can I get Carsoft to work with my OBD1 '95 M3? (also have a OBD1 '94 Canadian E36 318is) I have a 17" Dell Laptop I use for all my Car suff (TIS, Bentley) and would love to have a tool to read/access/reset codes...

And if it will work, whats the all up cost for the program and interface and what are all the things I need? (assume Cable and program, any more?)

Thanks!

[David Mc]

My vehicle does not have an OBDII port and I run Carsoft 6.5 on a Dell M65 Laptop. All up cost for the interface and software should not run more than about $150.

[KnudsonsM3]

congrats

[Corey G]

Not ot thread jack but does anyone have carsoft in english they can send me or a link to where I can download, I have it in german and it driving me crazy. IF so please PM me.

[EdirtySicks]

bookmarked!

[psyyambmw]

Dear David Mc

I jumped to the ebay search for the Carsoft hardware right after I crushed on ya thread yesterday.

I finally came across to this http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&tc=photo&ih=012&category=43989&viewitem=&item=220212511824&_trksid=p1713.m153.l1262

Do you think this thing gonna works w/ ya Carsoft software?

Thanksssssss in advance,

George :)

[David Mc]

This interface looks exactly like the one I use.

[98dinan3]

Are you guys all using this through a serial port? I've heard serial to USB adapters can cause problems.... any info would be appreciated as my laptop does not have a serial port, but has 4 USBs. Go figure... Also, is anybody running this with Vista?

[BJO]

Are you guys all using this through a serial port? I've heard serial to USB adapters can cause problems.... any info would be appreciated as my laptop does not have a serial port, but has 4 USBs. Go figure... Also, is anybody running this with Vista?

I have run it on USB to serial links fine. Just make sure you have the proper drivers and its good.

I haven't tried it in Vista.

[a32guy]

So would I be able to datalog live engine information with this on an OBD1 car? Say spark advance, rpm, injector duty cycle, etc?

[BJO]

So would I be able to datalog live engine information with this on an OBD1 car? Say spark advance, rpm, injector duty cycle, etc?

I have only seen it work on OBD2 cars. IF someone has gotten it to work on OBD1 please chime in.

[David Mc]

Yes, I can view O2 sensor readings, timing, vanos advance, rpm, coolant temperature, airflow, injector signals etc. all using the 20 pin connector under the hood. OBD2 was not adopted as a standard on Australian cars until recently.

[a32guy]

Very good information. Thank you David. This australian car, was it a bosch or siemens ecu?

[David Mc]

Carsoft identifies the DME as BMW Part 1429861 which is a Seimens 5WK9-0322.

[cjsdad1]

I have the carsoft software and the cables but I cannot "talk" to either my cars. I keep getting a cannot find Diagnostic cable error. Could any body tell me what port setting they use, what lights are on when the cables are plugged into the cars?

[BJO]

I have the carsoft software and the cables but I cannot "talk" to either my cars. I keep getting a cannot find Diagnostic cable error. Could any body tell me what port setting they use, what lights are on when the cables are plugged into the cars?

look at your laptop port settings first:
start menu>all programs>right click on my computer>left click on properties>hardware>device manager>ports. See what Com port your laptop has. Then use that setting in Carsoft.

[cjsdad1]

they are both set to com 1. If I change it the error changes to cannot open com.
Are you using the default settings IE.. flow control xon/xoff, baude rate ect...

[BJO]

they are both set to com 1. If I change it the error changes to cannot open com.
Are you using the default settings IE.. flow control xon/xoff, baude rate ect...

set com port to 9600, no flow control, no xon/xoff, 8 bits.

[cjsdad1]

what about parity and stop?

[David Mc]

The cause of this problem is more than likely a dud cable. Disconnect the cables from the interface and check continuity with an ohm meter. I have never had to alter any baud rate, parity, stop or flow control data from the system default settings. I am assuming that you are attempting diagnosis with the ignition on (dash lights illuminated but engine off).

[cjsdad1]

Thanks for the info
I am returning the unit for an exchange.
I ohmed the db9 serial cable from the laptop to the "box". When I plug the box in I get a power light and all green lights except service. I think the box is bad.

[David Mc]

If you have problems when you receive the exchange unit, PM me and I will help where I am able.

[cjsdad1]

Cool thanks.

[SkyladyZ]

Can anyone help me with my carsoft??

I'm running version 6.5 and am having problems erasing the fault codes as well as reading ABS

The only fault code that i could erase was the EWS fault code.

Also i have follwed exactly what this thread has said to do the information.

Please help

Thank you!!!

[DusM3]

This interface looks exactly like the one I use.

Good job! Now I can look at installing mine as well. Which vendor supplies the interface, or are they all the same and you need to be lucky to get a working unit?

[David Mc]

Carsoft 6.5 does not read my ABS/ASC module either. I think this maybe due to the fact that the OBC is locked (i.e. does not allow access to the module). I intend to unlock the OBC using the Test 19 function and attempt a diagnostic with the module unlocked to see if Carsoft will read the data then, but have not gotten around to it yet - I will keep you posted. I have encountered one member in Germany who was using defective Crack Software and we managed to correct the problem by using a version known to work, but otherwise you should be able to access live data and reset all modules detected. If not - check all vehicle fuses.

As far as the interface goes, if you are using an interface similar to the one pictured in this thread it should work - if not then the problem is more than likely software rather than hardware related.

Update 20 April 2008 - I tried unlocking the OBC and running a diagnostic with it unlocked - no change in the number of modules accessible. The only modules I have not been able to access are the LCM (this information - VIN number, distance travelled since last service etc is available on my car by running a cluster test), EWS (I don't have an alarm fitted) and ABS/ASC. For the cost of the interface, it is still the best value around as I can diagnose and reset DME, Aibag, ZKE, EGS and Instrument cluster fault codes as well as initiating autolocking options, changing between display units (temp in F or C, distance in miles or kilometres etc.), viewing live data and resetting service and oil change intervals.

[BMWsupport]

I'm using carsoft 6.5v
What are the differences n software abilities after SP1 install?
Does anything change? Any new features SP1 adds OBD1?

[David Mc]

This is the info from the Carsft site re SP1:-

BMW V6.5 Service Pack 01
This SP corrects the following known issues :



1) AB Fault Code Indication
2) DME Status and Fault Code Indication
3) DDE Fault Code Indication
4) Carsoft.exe, Compatibility improvement</SPAN>
5) New Features : iDrive Setup :
(under special functions)
- Change of Date, Time : settings
- Change of Brightness settings
</SPAN>- Coding of Languages settings
- Coding of Units settings
</SPAN>- Coding of Steering wheel buttons set.
- Change of RPA settings
</SPAN> - Coding of PDC settings
- Coding of Light settings
</SPAN> - Coding of Power Lock settings

[Gatsby740il]

David Mc... you, sir, ARE THE MAN! I can't tell you how much I appreciate your detailed install instructions! I had been having the same "connection" troubles as most.. but after following (to the letter!) your instructions + Update from Carsoft... I am finally able to connect! Thank You -- owe ya one!

I do have a question...E38 Programing, Live Data work flawlessly... but whenever I try and perform the Total Diagnosis or individual diagnosis of any item in that same menu... it appears to start initializing... then I get, "Carsoft Has Encountered A Problem And Needs To Close..",error followed by a shutdown of the program. Any idea on what I can do to fix this? I am connecting under the hood because my OBC In-Car connector doesn't seem to work (like the others I have seen here who have the same problem).

Hope you can help and look forward to your reply! Thanks Again! :cool

-Gatsby

[David Mc]

This is a common problem which is usually related to bad "Crack" files that are floating around. The folder that works contains 10 files including instructions whereas the bad folder contains only 6 or 7. I have PMed you with the info.

[naz]

I have seen a bittorrent search for 'carsoft 6.5+sp1+cracks' will this work? and will this be the english version?

Thanks

[David Mc]

I have seen a few bittorrent search sites so I am not sure. There is also a download of Carsoft software available here http://www.ecutool.com/productshow.asp?id=114&sortsid=547&sorts=BMW%20Tools which I think is v 6.5. Get SP1 from here http://www.carsoftinternational.com/bmwdownload.htm . If the "Crack" folder contains less than 10 files including instructions after you have downloaded the software, PM me.

[Voyd]

I have seen a few bittorrent search sites so I am not sure. There is also a download of Carsoft software available here http://www.ecutool.com/productshow.asp?id=114&sortsid=547&sorts=BMW%20Tools which I think is v 6.5. Get SP1 from here http://www.carsoftinternational.com/bmwdownload.htm . If the "Crack" folder contains less than 10 files including instructions after you have downloaded the software, PM me.

In the above link there is not a crack folder. Am I missing something here?

[David Mc]

The Carsoft 6.5 download contains a Crack folder.

[David Mc]

The download site above contains Carsoft 6.5 and Carsoft 6.1.4 but there are no Cracks specifically for 6.5, PM me re a RAR Crack file to use (About 3Mb in compressed form).

[psyyambmw]

I just successfully installed the carsoft an hour ago. I have to confirm that David Mc’s instruction really does work.

But my bad news is the readout. All modules failed to response as the pic below:
http://www.geocities.com/chapchai/immages/carsoft-report2-s.jpg

But can do the interval reset, all green lights on all the way (at start).

What is wrong, guys? :help

[David Mc]

PM me, this is usually fairly easy to fix.

EDIT 10/05/2008 sorry guys, had to delete my email details due to SPAM influx.

[psyyambmw]

pm sent

[David Mc]

I have pm'ed you some further info and have posted a copy here for the information of other members who may have run across the same problem:-

There are several possible reasons (assuming that you are attempting to run the diagnosis with the ignition switched on but engine turned off (dash lights should be on).

1. The "Crack" folder that you used may be incomplete. Check the folder, it should contain 10 files, including instructions. If not, email me and I will send you one that works.

2. Right click on your "Programs" folder from the "Start" menu and choose "Explore". Locate the Carsoft folder, which should be in the "Program files" directory. When you left click on the Carsoft Folder it should contain a folder called "BMW". Choose the BMW folder and make sure that it contains only one file with a "CS V6.5" icon. That file should be called CARSOFT. Double (left) click on the CARSOFT file and it should open the diagnosis screen. Click on the _____?_____ drop down menu and choose "Info about Carsoft" to make sure that it is version 6.5.06. If the version is 6.5.05, SP1 is not installed. If there are 2 "CS V6.5" icons, double click on each in turn to view the version information as described above. Delete the icon for version 6.5.05 and rename the other CS V6.5 file CARSOFT.

3. You may have a blown fuse or faulty cable. Check all the fuses in your car and attempt a diagnostic again. If unsuccessful, try another cable.

4. The battery in your vehicle may be low, check output voltage to make sure that it is >12volts.

[rrosscoe]

Finally, after 3 months of experimenting, copying and deleting files, computer harddrive purging and reprogramming I have succeeded in making Carsoft 6.5 SP1 work with my E36!

I can now conduct diagnostics and read live data and have access to all of those nice little extras like door lock programming etc..
hi David
I have have Carsoft 6.1 and it appeared to work for the most part but it did not do what I wanted it to do, specifically alter the tick over speed on 1997 525 tdi se. I have tried your suggestions to install 6.5, i have managed to install it (i think) but when i try to run a diagnosis i get a error stating that there is a problem with the diagnostic cable, now this is the same cable as did work with 6.1 so is it a problem with 6.5 or my cable?. I would apreciate any suggestions that you may have.
what i actually want to do is to up the tickover speed as i have a bit of rough idle.
cheers

[David Mc]

Rrosscoe,

Carsoft 6.1 will run using my interface but I am not sure about running 6.5 on version 1 interfaces. Cracking 6.1 is a lot easier than 6.5 however so I would suggest that the first thing you should do is to look at the Crack folder you used with 6.5 to make sure that it contains at least 10 files including instructions. If not, email me as per the previous posts.

[rrosscoe]

David,
The files i have are as follows,
folders
carsoft 6.5
carsoft_bmw65_crack
engelsk carsoft koder
bmwv65sp01eng
in the first folder there is,
folder eng
file readme
file usa license
folder warranty
autorun
and setup


second folder
instructions
file bmw
file bmwhlp
filecarsoft



the third folder is all the English error texts
the fourth is the sp 1update



do i have something missing as you say there should be 10 files and it appears that i do have 11 :eyecrazy
cheers

[David Mc]

rrosscoe,

The carsoft_bmw65_crack folder should contain 10 files, yours contains only 4. Email me.

[bongnak]

im leaning towards the purchase of this, but before i do, can someone tell me if they had success with sync'ing the ews with the dme? OH and thank you david mc. this is my only chance for me to fix my car without paying the dealer. Thank you

[martinosamigos]

This is the info from the Carsft site re SP1:-

BMW V6.5 Service Pack 01
This SP corrects the following known issues :



1) AB Fault Code Indication
2) DME Status and Fault Code Indication
3) DDE Fault Code Indication
4) Carsoft.exe, Compatibility improvement</SPAN>
5) New Features : iDrive Setup :
(under special functions)
- Change of Date, Time : settings
- Change of Brightness settings
</SPAN>- Coding of Languages settings
- Coding of Units settings
</SPAN>- Coding of Steering wheel buttons set.
- Change of RPA settings
</SPAN> - Coding of PDC settings
- Coding of Light settings
</SPAN> - Coding of Power Lock settings


HI David, I got carsoft 6.5+sp1+cracks from bit torrent, I downloaded the software with SP1 and the crack, by the way, the crack folder contains only 4 files. 3 executables and 1 text file instructions. My question, is the software with the cable only sufficient, to do diagnostic and read data from a BMW E39 20 pin connector? Or carsoft comes with a special hardware that we connect it to the laptop.

[David Mc]

You must have the interface box to use with your cables and the crack folder you have will not work properly. Drop me an email with an email address that can handle a 4mb enclosure and I will send you a working crack folder.

[fraseman999]

David, just registered on this forum thanks to you. I have been trying to get carsoft 6.5 to work on an my e60 530d 2004 for months. My old Packard bell broke and i bought a new sony vaio and was told the usb convertor was the problem. So sent for a pcmcia card for another vaio i had then sent for an express card for the newer one.
The only reason i new it was nearly working was that i could get live data. After trying forever i gave up. Then the other day my increased emissions light came on and i thought i would have another go and found your post.
It worked fantastic, done full diagnosis and told me what was wrong with my park distance control and switched of the engine light and its not came back on so figure that was due to low fuel.
The only light it isnt working with is my airbag light. Maybe cause the faults still there but its not telling me the problem. However this is a 2004 model so i am pretty pleased.
Does anyone know where you can get a list of the codes and also it gives you a bmw part no. and i have the etk disc but the numbers dont match. However bmw could tell me what it was.
Thanks again mate.

[thesk8nmidget13]

for some reason i did EVERYTHING exactly how you said but for some reason i am only at 6.5.05

i cannot get it to 6.5.06

thanks in advance

EDIT:

figured it out myself.

had to delete the CARSOFT65BMW files and just leave the CARSOFT file.


going to try again now

[Marco1973]

Hi DAVID (and other members),

The carsoft 6.5+sp1 I got has the crack folder which contains 4 files.
Do you have the adress or something like that, so I can get a correct version.
Thanks for the instruction you wrote earlier, sure to use it when I get the correct version. (and an old laptop).
There was a funny thing I read when I was browsing about carsoft etc.
someone wrote that you needed 2 serial ports, that is in my believe not true???
it is either OBDII or the 20 pin under the hood, that's what I thought....

I'll got the cable set from ebay, OBDII and the 20 pin and the BMW compatible interface V6.5 (guess this is the carsoft version it should use) and it stated that it is the Version 4).

A site (I could not find that site again, let you know when I will) stated that when digital connection failed, you could also try analog connection.
whats the main difference and is digital test better then the analog?

Hope to see your replies.
Thanks alot.

[David Mc]

PM me with an email address that will handle a 4Mb attachment and I will send you a working Crack folder. Early versions of Carsoft (circa v 3.1) used 2 ports rather than a single port as is used by v6.1, v6.5 etc.
When the software suggests an analog test in the event of failure of the digital test, it means that you should conduct a discreet test of the failed component using a multimeter rather than attempting to diagnose the component failure digitally via use of the Carsoft program.

[Marco1973]

I an not use PM or anything like that?
Stange but true, but the CP does not show it.
I think I am going to open a hotmail account and post it here afterwards I delete the post and mailaddress.

Keep in touch.
thanks

[David Mc]

Marco, I have emailed you with some info.

[MaxVQ]

Has anyone seen Carsoft 6.5.06 that read modules and works fine (set the clock to 24hour!!) , but shows zeros for the live DME data?

Thanks!

[roo97ss]

question about carsoft...

1. now it's reading 6.5.06, in german of course....anyone have english files

2. some of the codes have nothing with them, just a code.

ie zkw 66 and 67; airbag 116

any idea how to interpret these?

Joe

[98dinan3]

just to report I have carsoft running properly on Vista with a USB to Serial adapter... :buttrock

[ClayMan]

Anyone successfully aligned their EWS with this?

[maciska]

has anyone this soft: CARSOFT BMW ULTIMATE PRO 1.0, does it work with CS6.5 interface?

[David Mc]

There is a post here by BCOM320i about Ultimate Pro 1.0, but I am afraid I have not tried the program and do not know if it will run on a v6.5 interface.

[ClayMan]

Looks like I may be trying this soon. My main goal is to align EWS with DME on my S52 swap.

Also, is this able to change the instrument cluster odometer from metric (km) to imperial (miles) and vice versa? That would be a bonus!

[David Mc]

Carsoft does have a "Vehicle coding" function under its special functions menu, which includes changing display information between km and miles and consumption figures from mpg tp litres per 100 km. I have had no cause to try it so I don't know any more about it other than that it is listed under E46.

[NoWaY]

I have pm'ed you some further info and have posted a copy here for the information of other members who may have run across the same problem:-

There are several possible reasons (assuming that you are attempting to run the diagnosis with the ignition switched on but engine turned off (dash lights should be on).

1. The "Crack" folder that you used may be incomplete. Check the folder, it should contain 10 files, including instructions. If not, email me and I will send you one that works.

2. Right click on your "Programs" folder from the "Start" menu and choose "Explore". Locate the Carsoft folder, which should be in the "Program files" directory. When you left click on the Carsoft Folder it should contain a folder called "BMW". Choose the BMW folder and make sure that it contains only one file with a "CS V6.5" icon. That file should be called CARSOFT. Double (left) click on the CARSOFT file and it should open the diagnosis screen. Click on the _____?_____ drop down menu and choose "Info about Carsoft" to make sure that it is version 6.5.06. If the version is 6.5.05, SP1 is not installed. If there are 2 "CS V6.5" icons, double click on each in turn to view the version information as described above. Delete the icon for version 6.5.05 and rename the other CS V6.5 file CARSOFT.

3. You may have a blown fuse or faulty cable. Check all the fuses in your car and attempt a diagnostic again. If unsuccessful, try another cable.

4. The battery in your vehicle may be low, check output voltage to make sure that it is >12volts.

I have the same problem
I have 745 li 2004 and i recive my carsoft 2 week back but till now i cann't make it work
still gives module not responding:mad
could you help me, i need detailed step to make it working
and i got it from
http://cgi.ebay.com/ebaymotors/BMW-CARSOFT-6-5-READ-ERASE-CODES-OBD1-2-W-SOFTWARE_W0QQitemZ170218560168QQihZ007QQcategoryZ4 3989QQssPageNameZWDVWQQrdZ1QQcmdZViewItem (http://rover.ebay.com/rover/1/711-53200-19255-0/1?type=3&campid=5335818596&toolid=10001&mpre=http%3A%2F%2Fcgi.ebay.com%2Febaymotors%2FBMW-CARSOFT-6-5-READ-ERASE-CODES-OBD1-2-W-SOFTWARE_W0QQitemZ170218560168QQihZ007QQcategoryZ4 3989QQssPageNameZWDVWQQrdZ1QQcmdZViewItem)
and he provide my download link that contains only two setup files

http://www.millisi.net/download/OBDII/BMW65.rar

that i use but keep gives me module not responding
and i already download carsoft from torent but crak folder contains 4 file only so could you send me the working crak to
al_fares_sa@hotmail.com

and if you can test the program on previous link and confirms it working or could provide alink for your copy if you don't mind


thanx for you

[David Mc]

Email sent with info requested.

[David Mc]

This link may be helpful if anyone is having problems communicating with their car after successfully installing Carsoft http://avtodiagnostika.ru/content/diagsoft/carsoft/Carsoft%20BMW%206.1%20Common%20Solutions.pdf

[getghost]

I bought my carsoft from the same vendor as noway did... After several tries of installing I finally got it to work. I checked the version and it is v6.5.06. Everything was going great, hooked it up to the car and booyah diag cables faulty error...This sux, I contacted seller and have had no luck...I believe something is wrong in the software as everyone seems to get this but I can't find a fix...I looked at the pdf that david posted but it doesn't tell me much. I have a pcmcia to serial adapter and have been having com port problems with it. So I unhooked the cables and ran total diag and the carsoft error returns with cables faulty error...How can they be faulty when they are not hooked up...any ideas would be great thnx:help

[David Mc]

I don't think that the Crack supplied with your software is working properly. I have emailed some files and suggestions to NoWaY which I think will fix the problem. PM/email me with an email address capable of handling a 4mb enclosure and I will send you a copy of the files and info.

[getghost]

hey ok, when I click your name it doesn't give me the option to send email... send to getghost@comcast.net (getghost@comcast.net...thanx) I really need to get this I have a car waiting to be torn down for some trouble but I would love to watch the data before I get to work... Thank you

[David Mc]

I have emailed the info to you but this account cannot handle the 4mb Crack file enclosure.

[getghost]

Yes, I got the crack file...contains 10 files. I am working on reinstalling this now, so I will post results back. Thank you!!!!!!!!!!!!!

[NoWaY]

Email sent with info requested.

thank you very much for response

just one q
u said in your email
5. Instal SP1
ok i download before from carsoft website ( or it was included in torenet download I'm not sure but i think it from website ) faile named
BMWv65SP01ENG ------ this i think SP1

amd after reading your msg i go to the website and found this one
BMWv65SP011ENG ------ this i think SP1.1

which one i should use? and ur xp pro or home? with sp1 or sp2 or sp3? fully updated?
thanx

[getghost]

this is insane!!!!!!! i followed directions as stated, got version 6.1 working and looking for modules...wouldn't communicate-says module not responding...i have 6.5 interface...i bought from the same vendor as noway but now when i return to the link its dead...after messing around trying to get the software to talk to modules it comes back with "this is a ten time trial please register"...i must say this is getting really stuipid...is it this difficult? im running this trying on two computers at the same time to no avail....any ideas? can i eturn to version 6.1 working and then get the modules not responding worked out or what...I HATE CARSOFT!!!!!!!!!!!!!!!almost 10hrs in today...any ideas now?????

[David Mc]

If someone will nominate a site to host the files I will upload Carsoft 6.5, SP1 and the proper Crack files and we will have an end to all of the problems that members are facing with trying to get this software working.

[NoWaY]

http://www.4shared.com

this one is good
but did u try sp1.1?

[David Mc]

Thanks NoWaY! I am already using SP1.1 this is the link to the site to download Instructions, Carsoft 6.5, SP1 and the proper Cracks http://www.4shared.com/dir/7137899/6e9cd794/sharing.html

[NoWaY]

Thanks NoWaY! I am already using SP1.1 this is the link to the site to download Instructions, Carsoft 6.5, SP1 and the proper Cracks http://www.4shared.com/dir/7137899/6e9cd794/sharing.html
thanx for your fast response
i will try the whole set now
but try to remove the crack.rar coz the web site not allow any accses or change the name but i think u alrady add it in main program rar so no need for separate file any more :)
you didn't tell me which version of xp Ur using:
XP pro
or
XP home
and any service pack like sp1 or sp2 or sp 3? and is it updated up to date?

thanx for great help

[getghost]

David Mc is the man!!!!! Thank you noway for the site to host!!! And THANK YOU VERY MUCH David Mc for the time and effort!!!!! Carsoft is up and running. After downloading the files for the new hosted site, I had zero trouble with the install. I scanned the car and booyah codes everywhere...Awesome that it works, not awesome for codes everywhere lol. Is there a post for codes or can I post what I got here?

[David Mc]

Try plugging the codes into the bottom of this page
http://www.my330i.com/odb2.php if they don't work, post away. Glad to hear it's working for you. I run XP Home and XP Pro (both with SP2) on my 2 computers.

[getghost]

Thanks, I tried plugging them in and it didn't tell much. Some it didn't know at all...I also couldn't select and copy screen info to post here...although I thought I saw someone else do it? I must be missing something there, but anyway I'm going to email the file to you and you can see...Thanks

[wiki]

i hav bought the dignose cable which has 20 pin connector and two DB9 female plug,
as my laptop doesn´t have db9 connection. so i bought the usb conversation plug and connect them.
but the carsoft still giving me a error, that cable is not correctly attached.
as i read in carsoft manual that it doesn´t support USB conversation plug.
but some of you said it does worked.
could you guys help me plzzzzz.

[GimmieSumMo72]

you might have to configure the COM port on your USB connection to correspond with Carsoft

[wiki]

but my problem is i have two plugs, whereas in carsoft only one port could be set. here is the link from which i bought the wire.
http://cgi.benl.ebay.be/BMW-Diagnose-Interface-E30-E31-E32-E34-E36-E38-E39-E46_W0QQitemZ150245851165QQihZ005QQcategoryZ44189Q QssPageNameZWDVWQQrdZ1QQcmdZViewItem

[David Mc]

Wiki, If you have an interface with 2 plugs it sounds like it is for a very early version of Carsoft (e.g. v 3.1), not Carsoft v 6.5. Can you please post a picture of your interface.

EDIT: I have just looked at your interface and can confirm that it is the one used with the early versions of Carsoft (up to v 3.7). It is not suitable for use with the later v6.5 software.

[NoWaY]

mr.david did u test it on e65?

[David Mc]

Unfortunately I don't have access to an e65, but in every other case I have encountered the software performs as claimed, provided that it has been properly loaded and used with a serial port, PCMCIA card or properly configured USB to serial port adaptor.

[wiki]

thanksssssss David,
but do anybody know where could i get the early version of Carsoft.
or any other software which i could use to dignose the my E39 with two plug interface

[MaxVQ]

Unfortunately I don't have access to an e65, but in every other case I have encountered the software performs as claimed, provided that it has been properly loaded and used with a serial port, PCMCIA card or properly configured USB to serial port adaptor.

Really?
On the 525/528/530 Live data does not work. It shows zeros, BUT it does work on the 540.

Auto Lock does not work. You can set the feature, but the locks don't lock when at speed.

[LPCapital]

Hello David MC,
I have a couple questions you might be able to help me with:
1) I was reading Carsoft lets you reset the adaptation values of the DME: are we talking about things such as LTFT (long term fuel trimming)?
2) How strong are the live data functions? Can I for example record different parameters, export the in a CSV value and read them in excel? Let's say I wanna see if I'm running reach or lean and I wanna check what would be the O2 voltage at different RPM, under differnt load condition: can I do it?
Thanks

[ClayMan]

Anyone had success with the carsoft interface that looks like this?

http://www.jeffelectronics.com/ebay/BMW-0.jpg

[MaxVQ]

Anyone had success with the carsoft interface that looks like this?

http://www.jeffelectronics.com/ebay/BMW-0.jpg
This is the one I have. I can read and reset all modules on my car.
BUT the Live Data shows ZEROs. I don't know if this is a Carsoft problem or this box.

[GimmieSumMo72]

Anyone had success with the carsoft interface that looks like this?

http://www.jeffelectronics.com/ebay/BMW-0.jpg

I've got one like this...

it works well, but i cant figure out how to read the reports it spits out!

[David Mc]

This link has a clip of the Carsoft Live Data function in action
http://forums.bimmerforums.com/forum/showpost.php?p=13087741&postcount=39
The only way to record live data is to use your computer's Printscreen function to copy and paste the info into a word document - cumbersome but it beats scribbling 5 pages of live data out with a pencil. The Carsoft 6.5 review by DJGenius shows most of the functions available on Carsoft, which does not support DME remapping or fuel trim adjustment.

[designer485]

Are the crack files already in the folder that can be downloaded or do i need to get them from somewhere else. Can you send them to me David? I have been trying to get the program running with no luck yet.

[David Mc]

The program folder on the hosted website should contain everything you need. I have also uploaded a few other files that may be of interest, such as BMW Trouble Code definitions, a PDF e36 owners manual and some repair guides.

[getghost]

I'm having trouble with the tiff file, the fault codes file...When I download it it pops up in another window and displays some funky characters and then stops...Any ideas on that?

[designer485]

After i get eveything installed...that finally worked...the program is asking me for an authentication code? Maybe i am doing something wrong?

[David Mc]

I have re-loaded the M52 fault code file as a PDF, try it now. If Carsoft is asking for an authentication code, the software has not been cracked properly, I suggest you print out the installation instructions and reinstal the software.

[designer485]

Thanks, thats what i figured...i just wanted to make sure.

[gtxragtop]

This link has a clip of the Carsoft Live Data function in action
http://forums.bimmerforums.com/forum/showpost.php?p=13087741&postcount=39
The only way to record live data is to use your computer's Printscreen function to copy and paste the info into a word document - cumbersome but it beats scribbling 5 pages of live data out with a pencil. The Carsoft 6.5 review by DJGenius shows most of the functions available on Carsoft, which does not support DME remapping or fuel trim adjustment.

Interesting, my 6.5 version has the option to reset the DME
Special functions
Adaptation values
DME/ME ERASE

Have not tried it however. Not sure where you read the current values.

[getghost]

Got it...pdf works...thank you sir...

[getghost]

So I see the coding tabs, dme coding and lcm coding, what are these for? I click it and it says reading coding data then says turn ign off-turn ign on and then i press write coding...is this for module replacement? So the new module gets the info the old module had?

[David Mc]

I have also seen but not used the coding functions and agree that they appear to be used to transfer data to a new module during replacement.

[getghost]

I think it has been noted or posted before but can I recode a replacement cluster with the lcm recoding?...I have also found the repeative code 111 which is torque converter clutch circuit open...Where is the solenoid located this is the gm tranny... Is it internal in the second small pan, any ideas on how to test or locate so I can ohm it out...thnx

[JRW21]

Anyone had success with the carsoft interface that looks like this?

http://www.jeffelectronics.com/ebay/BMW-0.jpg


Ok, one more question on this unit.. Will this realign ECU/EWS for my new tune?

[MaxVQ]

JRW21 (http://forums.bimmerforums.com/forum/member.php?u=89262) that is the interface that I have. It does seem to work to get/clear codes, but Live Data reads all zeros. I don't know if that is the car (Siemens MS43) or the interface box.

[Malina]

Has anyone tried ELM327 USB to OBDII tool with CarSoft?
http://www.scantool.net/products/product_info.php?cPath=8_6&products_id=32

[madspeed]

does anyone know if this can be used for the ABS ?

[David Mc]

Be patient, it sometimes takes a while.

[JRW21]

JRW21 (http://forums.bimmerforums.com/forum/member.php?u=89262) that is the interface that I have. It does seem to work to get/clear codes, but Live Data reads all zeros. I don't know if that is the car (Siemens MS43) or the interface box.

Max, thanks for the reply. Can you confirm if this will realign an ecu on an ecu tune swap?

[MaxVQ]

Max, thanks for the reply. Can you confirm if this will realign an ecu on an ecu tune swap?

The only option I see that has "sync" is "Sync EWS <--> Engine Control Unit"
However, the next time I connect it to my car I will check all the menus.

[MaxVQ]

Max, thanks for the reply. Can you confirm if this will realign an ecu on an ecu tune swap?

The only option I see that has "sync" is "Sync EWS <--> Engine Control Unit"
However, the next time I connect it to my car I will check all the menus.

[JRW21]

Thanks, I would really appreciate it.

[zobo1982]

Hi David,

My cd doesnt seem to have a cracks folder??

[David Mc]

If you go to the shared website listed in the "Carsoft Success" thread, you can download the program and cracks from there.

David Mc

[madspeed]

anyone has any luck scanning the ABS with carsoft ?

[MaxVQ]

Yup:

Single diagnosis ABS / ASC - Status: ERROR ! Module info :
ABS / ASC / DSC Version : Bosch ABS 5 ! BMW Part Nr. : 6 75 63 42
Hardware Nr. : 53 ! Software Nr. : 3.30
Diagnose index: 11
Code index : 9
Bus index : 60
Production Date: 17/00

6 Front right speed sensor faulty OR ABS-inlet valve
7 Front left speed sensor faulty OR ABS-inlet valve
59 Fault, ASC shutoff valve - Single diagnosis completed !

These errors were caused by the emission test dyno.

[MaxVQ]

Max, thanks for the reply. Can you confirm if this will realign an ecu on an ecu tune swap?

I think you can... Look at the attached graphic:

[madspeed]

I get the error saying ABS module does not respond. everything else scans without a problem. any idea what I should be looking at ?

[smracing85]

Just downloaded everything from the file share site. I've never had any carsoft software before. Started the setup but during the install an error appears: Severe, Path too long-Aborting (error code 80/1)

I didn't change any of the default installation paths (left it at C:program files/carsoft) What's going wrong? Fyi i'm running '02 XP media center

[David Mc]

Try unzipping the software first and then reinstalling. Carsoft wont read the ABS module on my E36 either.

[smracing85]

It was unzipped, it runs through the whole setup until the progress bar reaches the very end, then that error box pops up. I then click "ok" and it says setup has completed the install, then when i open carsoft it says installation was incomplete.
I'm going to try some bit torrent versions of 6.5 then just use your SP1 and crack files.

Thanks for all the hard work i'm sure you put into this, you're helping everyone out big time.

[David Mc]

Is it possible that the download was not complete? I would try downloading the software again first as it has been tested and verified as operational.

[slimgrip318i]

Cheers David, worked a treat here!

Just need to understand the results now ;)

[thesk8nmidget13]

again anyone have success with an obd 1 car???

anyone out there?>

[slimgrip318i]

Anyone know what these mean?

BE LCM internal error
&
BF instrument cluster internal error

Or if anyone knows of a site or decent plain english help file id be eternally grateful.

[zobo1982]

David,

You seem to be the man.

Finaly got Carsoft installed from the Share site.

Borrowed a Laptop with a RS232 port.

Connected, all well so far. Run any diagnostic, gets about 3 seconds in, Carsoft has encountered a problem and need to shut down.....AARRRgggghhhhhhhhhhhhhhhhhhhh

Tried reinstaling, exactly the same problem. Firewall is off.
PLEASE HELP ME BEFORE INSANITY KICKS IN

[David Mc]

Start the program, click on the _____?_____ drop down menu and choose "About Carsoft...". The program should display version information which should be v 6.5.06. If it displays v 6.5.05, (assuming that this was a first time instal or that you had properly purged any previous files before installation) follow step 2 of this link to troubleshoot the problem http://forums.bimmerforums.com/forum/showpost.php?p=12865612&postcount=54
BTW this file http://www.4shared.com/icons/16x16/exe.gifBMWv65SP011ENG.exe (http://www.4shared.com/account/file/48143303/5179f780/BMWv65SP011ENG.html?sId=P6t00iFay6ymnLM4) is SP1, which I assume you also downloaded with the Carsoft Software.

[BMWilli]

subscribed and bookmarked
thanks!

[zobo1982]

Thanks David, it seems to work now.

I have run a full diagnosti and it came up with several errors. I decided to erase the DME errors and rerun the Diagnostic. It now reports no errors on the DME.

Also, seem to be getting a few Module does not respond

[zobo1982]

Just a thought, does anyone have a how to use set of instructions for the Carsoft program?

[bmwperson]

Can anyone tell me if carsoft can set the vanos to assembly/service position on the e39 m5? (s62 engine)

[David Mc]

No, Carsoft will not set the Vanos

[ClayMan]

Thanks for the help on getting this working David.

The Carsoft works on all diagnosis as promised, EXCEPT for what I needed it to do the most - align the EWS on my E36. I repeat, it CANNOT align the EWS on the E36. I have confirmed this with another who has tried to do the same. It works on same production dates on the E46, but definitely not on E36s.

Dammit. :(

[ClayMan]

Anyone have a working version of Carsoft Ultimate Pro 1.0 that they are willing to share? (Please PM me) Gonna try whatever I can before I give up on this EWS align and go to the dealer...

[David Mc]

Clayman, I have never tried this with Carsoft, but did you perform a single diagnostic on both the DME and EWS modules and clear any faults before running the alignment?

[zobo1982]

David the man,

Carsoft is all working fine now.

I run a full diagnostic, deleted all the cides and re-ran it. Only problem i have left is a code coming up on the instrument cluster section. It says BF Instrument cluster internal Error. Does anyone now what this means????

The cluster seems to be fine, the only thing i would say is the Red light behind the temp gauge comes on when yoy first turn the key to position 2, but it goes out straight away. oh also, i have fitted angel eyes and they flash again, when you first turn the key to position 2 but go out straight away (these are wired throught the side lights so you only get the rings when you turn them on)

any ideas would be appreciated

[ClayMan]

Clayman, I have never tried this with Carsoft, but did you perform a single diagnostic on both the DME and EWS modules and clear any faults before running the alignment?

Good idea... Tried it but still no good. Looks like to the dealer it is! :rolleyes

[98dinan3]

Clayman... Bimmersport can now do EWS realligns... they'll likely be cheaper than the dealer, and you can rest assured Charlie does great work.

[SimonSingh]

Where did you get your cable from Zobo?


Dear David Mc

I jumped to the ebay search for the Carsoft hardware right after I crushed on ya thread yesterday.

I finally came across to this http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&tc=photo&ih=012&category=43989&viewitem=&item=220212511824&_trksid=p1713.m153.l1262 (http://rover.ebay.com/rover/1/711-53200-19255-0/1?type=3&campid=5335818596&toolid=10001&mpre=http%3A%2F%2Fcgi.ebay.com%2Febaymotors%2Fws%2 FeBayISAPI.dll%3FViewItem%26tc%3Dphoto%26ih%3D012% 26category%3D43989%26viewitem%3D%26item%3D22021251 1824%26_trksid%3Dp1713.m153.l1262)

Do you think this thing gonna works w/ ya Carsoft software?

Thanksssssss in advance,

George :)

Is is possible to fabricate a cable out of an old serial cable and some paperclips to go into the Diag port, using the information on the eBay auction?

EG:


====================
DB9 Female <-------------->BMW connector
1+2 -----------19 (Signal Ground)
4 -----------17+20 (ISO 9141-2 K Line)
8 -----------15 (ISO 9141-2 L Line)
9 -----------14 (Battery Power)

=====================

[Darkknight74]

are the ebay cables any good?

[DJ Genius]

The thing about it it's not the cables that are most important in the kit. It's the interface unit. Cables are just simple cables to transfer all the data and information. Interface is doing all the THING - coding and counting stuff. That's why it is believed Chinese kits aren't as good as original, because they didn't copy the interface as good. But... thing's changed and we all know those little f***ers are very clever, so they've actually improved over the time and made pretty good copies that work 90%-100% as good as original.
Just to make things clear, take a look at the cable and interface schemes:
Cable scheme:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/Cab_bmw_small.jpg
Big resolution:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/Cab_bmw_large.jpg
Interface scheme:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/schema_small.jpg
Big resolution:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/schema_large.jpg

http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/IMGP0010.jpg

[mgthompson]

Without the firmware for the AT89C2051 processor on the little PCB you won't get very far making your own interface.

[SimonSingh]

The thing about it it's not the cables that are most important in the kit. It's the interface unit. Cables are just simple cables to transfer all the data and information. Interface is doing all the THING - coding and counting stuff. That's why it is believed Chinese kits aren't as good as original, because they didn't copy the interface as good. But... thing's changed and we all know those little f***ers are very clever, so they've actually improved over the time and made pretty good copies that work 90%-100% as good as original.
Just to make things clear, take a look at the cable and interface schemes:
Cable scheme:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/Cab_bmw_small.jpg
Big resolution:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/Cab_bmw_large.jpg
Interface scheme:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/schema_small.jpg
Big resolution:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/schema_large.jpg

http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/IMGP0010.jpg


Without the firmware for the AT89C2051 processor on the little PCB you won't get very far making your own interface.

Thanks for the info guys

[zobo1982]

Hi all, The cables came with the unit of Ebay. Be warned, purchasing from ebay 99% of the time means the software is copied and will not work. Finaly got mine working with the help of DavidMC.

Just another note for you all:

When you get carsoft finaly working, when you use the vin/milage reader, the milage will be read in kilometers not miles (even if you set the carsoft to milage). I sh#t myself when the reader came back with 131,000 when the instrument read 82,000. This can be confirmed if the mileage tamper dot is not shown (the dot appears with any attempt to change any milage details on the cluster, it is in between the km or milage trip meter and the designation to km or m)

[GEN3RIC]

My cables should be here any day now. Already have the software up and running, awaiting connection... I bought this setup, on the advice of DavidMc (http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&viewitem=&item=120269662690)

[puppy]

Hi!
I read your success story with carsoft & did exactly as you said and i was pretty much successfull too. Though most of the modules it could not read but it gave me error code what i was looking for. I think you are great. Now i have the error code but i cannot get much out of it, so may be you can help me with this :
I have X5 2001 model and my DSC/ABS/BRAKE lights are ON. the error code carsoft gave is :
Supplier : Bosch
Device Nr:1423955
Hardware Nr:29
Diagnose Index :10
Bosch Hardware Nr :00000000000
Bosch software nr : 648
Production Nr:002
149 CAN - ABS/DSC wheel speeds

It seems like wheel speed sensor, but which wheel?

Please if you could help me?




Finally, after 3 months of experimenting, copying and deleting files, computer harddrive purging and reprogramming I have succeeded in making Carsoft 6.5 SP1 work with my E36!

I can now conduct diagnostics and read live data and have access to all of those nice little extras like door lock programming etc..

[DJ Genius]

Hi!
I read your success story with carsoft & did exactly as you said and i was pretty much successfull too. Though most of the modules it could not read but it gave me error code what i was looking for. I think you are great. Now i have the error code but i cannot get much out of it, so may be you can help me with this :
I have X5 2001 model and my DSC/ABS/BRAKE lights are ON. the error code carsoft gave is :
Supplier : Bosch
Device Nr:1423955
Hardware Nr:29
Diagnose Index :10
Bosch Hardware Nr :00000000000
Bosch software nr : 648
Production Nr:002
149 CAN - ABS/DSC wheel speeds

It seems like wheel speed sensor, but which wheel?

Please if you could help me?
There is no such thing as wheel speed sensor. The only sensor in ABS system is ABS sensor. The sensors are located in the trailing arm at the back of the hub. Give them a good clean with WD40, that might help. Then reset the error with a Carsoft and give another test.

[adambufano]

I have all lights but the service light on when I am plugged in the to OBDII and the 20pin is this correct?

[ClayMan]

Mine only came with the round 20-pin connector, and it works perfectly fine on my OBD2 E36. Except for the damn EWS align.

[David Mc]

Yes, the service LED only comes on whilst you are resetting the oil service/inspection.

[xdream]

nice

[xdream]

must get post count

[GEN3RIC]

must get post count
Just so you know..this is how you get banned from Bimmerforums. Might wanna not do that for the sake of not getting banned :az

[alirz]

Hello, im a newbie at this. Tried saerching and reading up but confused.
This car soft kit and the sfotware it comes with ( on ebay, or anywher else)

What can you do with it? I know this is not the full DIS kit.
but one reason i wanted to know was that does it activate the alarm system for the BMW ( DWA) the list of supported features on most ebay sites says that it does not do that for a E46.. any ideas.
if someone could please point me to a place where all supported features are listed, ill greatly appreciate

[cdrshm]

Mine only came with the round 20-pin connector, and it works perfectly fine on my OBD2 E36. Except for the damn EWS align.

Anyone know where to find just a cable?

I have the software and a Laptop with a db9 on it, just looking for the cable?

I have a 2001 E46

Thanks

[DJ Genius]

Hello, im a newbie at this. Tried saerching and reading up but confused.
This car soft kit and the sfotware it comes with ( on ebay, or anywher else)

What can you do with it? I know this is not the full DIS kit.
but one reason i wanted to know was that does it activate the alarm system for the BMW ( DWA) the list of supported features on most ebay sites says that it does not do that for a E46.. any ideas.
if someone could please point me to a place where all supported features are listed, ill greatly appreciate
Look at my sig, there is a nice Carsoft v6.5 review done.



Anyone know where to find just a cable?

I have the software and a Laptop with a db9 on it, just looking for the cable?

I have a 2001 E46

Thanks
You need an interface as well, mate. As I mentioned before, the interface (the small box that cables plug in) is 90% of all the kit. It's like a brain of the kit, the most important part. NOT THE CABLES!!!

[ckgixxer]

I need help I am riping my hair out for the 2 weeks trying to get my carsoft 6.5 to work. I tried David 4 shared download and I go to:

setup.exe.

when it opens I goes thru the normal install but at the end it comes up with a severe error

Path too long - aborted 80/1

then I exstract the crack folder to the programfiles/carsoft and that goes thru
and when I download sp1 it comes up with files not found.
After all that when I open it, it comes up with:

carsoft v6.5 incomplete!!!!!

I tried it on 2 lap tops with the same errors sso I think it something I am doing.

Any help would be great before I go bald

My email is skilpatrick@stny.rr.com

Thankk you
Chris

[DJ Genius]

You need to extract whatever you downloaded into your C:\ drive, try avoiding long path names (it's the name where your files are located "C:\Program Files\Johns Folder\Diagnostics\Carsoft\BF_Files Folder" and etc.) You can see your path at the top of your explorer. Try avoiding this type of paths, so instead place the extracted files in "C:\Carsoft files\".
All the rest doesn't work simply because it hasn't installed it fully and properly.

[thesk8nmidget13]

after finding out that carsoft cant align ews in obd 1 cars i have decided to sell my carsoft with usb to serial connector from radio shack and also the carsoft software all for 110 shipped.

i paid 120 and then another 30 for the usb to serial.

feel free to pm me.

wish i has obd 2 :(

[stevek1490]

I'm completely new to this, but have the software working and waiting for my cables to arrive.

Does my 96 E38 (750iL) have the OBD 2?

[GimmieSumMo72]

yes it does

[ckgixxer]

The path is c:/carsoft/bmw I do not why it is saying path too long? Does anyone have a software cd that I can use? I will pay shipping back and fourth!!!

Thank you

Chris


(oo\(lll)(lll)/oo) e46 vert

(oOO\(llll)(llll)/OOo) e39 m5

[David Mc]

Chris,

Download the Carsoft v6.5 software, SP1 and installation instructions from here http://www.4shared.com/dir/7137899/6e9cd794/sharing.html .

The SP1 file is the one named BMWv65SP011ENG.exe . Follow the installation instructions to the letter (no shortcuts). I have yet to hear from someone who has loaded software from this site correctly and could not get it running.

[DJ Genius]

The path is c:/carsoft/bmw I do not why it is saying path too long? Does anyone have a software cd that I can use? I will pay shipping back and fourth!!!

Thank you

Chris


(oo(lll)(lll)/oo) e46 vert

(oOO(llll)(llll)/OOo) e39 m5
OK, I get it now. The path is too long in archive .rar file. There are too many folders in other folders and etc. So you need to double click on the Carsoft archive file and actually go inside .rar file, you should see the files that are compressed in there. Go inside the folders there and extract the files manually. That's what I did. If you still have questions, post in here and I'll make step by step tutorial how to get away from this.

[ckgixxer]

Yes I think you got it dj genius, I would love a tutorial on manually opening rar files. This is the first time I used a rar file so I am new to this. Everyone thank you for all your help, I really thank you for your valuable time!!!!!!!!!

Thanks again
Chris

[GEN3RIC]

Anybody have Carsoft Ultimate Pro 1.0 working? It looks like it should work with anything OBDII as well.

[DJ Genius]

Working with compressed archive files (*.rar)
First of all you need to have compressed archive file with an extension of .rar, something like this "FileName.rar".
The easiest way to extract the files is press the right mouse button over the file you want to extract and choose the option "Extract to FileName\", that means it's going to extract everything into a created FileName folder in the same directory the original file is:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture1.jpg

After the extraction you should have FileName folder in the same directory as your compressed archive file FileName.rar is.
But sometimes this easy way doesn't work. For example if there is a long path inside the compressed file, like folder in another folder and that folder is placed in another one and etc. So to extract those files you'd need to extract them manually. To do so you need double click the left mouse button on the file you want to extract, you should get inside the compressed file and see all the files compressed:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture2.jpg

Go inside the "BMW" folder and select all files except "ENG" (click on every file holding CTRL keyboard button), because this particular folder is causing that "Path too long" error:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture3.jpg

Then press the "Extract To" button/icon on just below the MENU bar and the other window should pop out. You need to select your C drive on the right hand window and you should get "C:\" in "Destination Path" small window, in addition, wite "CARSOFT\" in there so it would look like this "C:\CARSOFT\":
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture4.jpg

Next, click OK button, all selected files are extracted to the folder "CARSOFT" on drive C:. Now we need to extract the last folder "ENG" (remember, we left it unselected before). So we select only the folder "ENG":
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture5.jpg

And extract it into the folder "C:\CARSOFT", like here:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture6.jpg

It looks like everything's done, so go and double check if all the files were extracted. Go to the folder "C:\CARSOFT\BMW" and that's what you should see:
http://i156.photobucket.com/albums/t30/djgenius10/DIYs/Carsoft/RAR%20extraction/Picture7.jpg

If you still get some mysterious problems, let us now:D
DJ

[GEN3RIC]

Got mine running, and now I am having trouble decrypting what the codes mean.. Ive got DME, ZKE, AIRBAG and INST CLUStER errors and the specific diagnostic readout are telling me "17 - Einspritzsignal ti (TQ) nicht plausibel" and "15 - Wegsignal vom Tachogeber nicht plausibel" (for the Instrument Cluster readout taht is).

I dont know what those are! Where can I converter these into a) english, b) something useful. :tongue

[GEN3RIC]

Oh, and the DME spat out
230 - Regelfreuens Lambdasonde Bank 2 Fehlershaft
while the ZKE just spat out 176 with no text.

[ckgixxer]

Dj Genius YOU ARE THE MAN!!!!!!!!!!!!!!!!!!!!!!!!! THANK YOU SOOOOOOOOOOO much for take the time to show me my wrong ways..

Thank you again

Chris

(oo\(lll)(lll)/oo) e46 vert

(oOO\(llll)(llll)/OOo) e39 m5

[David Mc]

Eric, for our English speaking companions the rough translation of your errors are (17) that the fuel injection signal is not within normal parameters and (15) that there has also been a problem with the signal to the tacho. The third (230) is probably the cause rather than effect as it means there is poor response from the Oxygen sensor in exhaust Bank 2. I would try cleaning the O2 sensor, clearing the codes and running another diagnostic.

[DJ Genius]

Oh, and the DME spat out
230 - Regelfreuens Lambdasonde Bank 2 Fehlershaft
while the ZKE just spat out 176 with no text.

You can translate them yourself, just use:
Babel Fish Translation (http://babelfish.yahoo.com/)

[GEN3RIC]

Eric, for our English speaking companions the rough translation of your errors are (17) that the fuel injection signal is not within normal parameters and (15) that there has also been a problem with the signal to the tacho. The third (230) is probably the cause rather than effect as it means there is poor response from the Oxygen sensor in exhaust Bank 2. I would try cleaning the O2 sensor, clearing the codes and running another diagnostic.

Thanks, I actually knew about the O2 sensor issue and gave it a cleaning and cleared the codes.. dare I say it runs betters. :devillook


You can translate them yourself, just use:
Babel Fish Translation (http://babelfish.yahoo.com/)
Thanks, but sometimes the direct translation from sites causes even more confusion :95 :D

[stevek1490]

I just got my interface, and cables (and am having to use a USB to Serial adapter because I don't have a notebook with a serial connection).

But it just errors, and says "Diagnostic Cable reports bad connection" Both the software and the computer are set for COM2. Any suggestions would be greatly appreciated.

[stevek1490]

Ok, little bit more info:

Running Vista machine, but didn't open any ports specifically for the CarSoft software.

Amber P light is on the black box (interface?) but no other lights.

[stevek1490]

I was successful in getting the interface to connect.

I'm only having one issue - I can't connect to the DME or receive Live Data from the DME it says it can't communicate with the module.

[GEN3RIC]

I couldn't connect to *SOME* things in the program until I ran as administrator and ran under XP SP2 compatibility mode.

[stevek1490]

I noticed some modules were accessible with the engine and ignition off, and some were accessible with the ignition set to position 2.

I just haven't had any luck connecting to the DME, or receiving live data from it. Everything else seems to work ok, and I even had live data from the transmission control module.

I'm going to check my fuses to see if any are out, as I saw that suggestion above.

[KyleAwesome]

The link is dead. It starts the download, but never actually receives any information, can someone reupload?

[DJ Genius]

I was successful in getting the interface to connect.

I'm only having one issue - I can't connect to the DME or receive Live Data from the DME it says it can't communicate with the module.
Is your car OBDI or OBDII?


The link is dead. It starts the download, but never actually receives any information, can someone reupload?
I don't know what you are talking about, cause I downloaded the file 5 sec ago, it works fine.

[stevek1490]

OBDII (96 E38, 750il)

[stevek1490]

I checked the fuses under the hood, and except for the 30AMP blower, are all good. I smelled an electrical burning smell from that fuse (the car is supposed to have a bad blower resistor that I haven't fixed yet - just bought the car last week).

About to check the fuses in the trunk...

[stevek1490]

The fuses in the trunk are ok too.

Not sure what else to check with this. Is it possible my DME is bad?

[stevek1490]

I have a couple of questions I would like to ask just to make sure that I am doing the right thing.

1) Can you read live data from the 20 pin connector under the dash?

2) I only have the amber P light on my interface. The K20, K17, and L15 blink when accessed, but do not stay solid green. Is that normal?

I originally tried this with a Vista notebook, but had no success. When I used an XP system, I was actually able to connect to most of the modules, read the error codes, and reset things like the airbag light, and SI indicator.

After checking the fuses in the car, I am still not able to pull live data from DME. I cannot connect to that Module at all.

Is it possible that this USB to Serial adapter is causing the problem?

From what I've read, most people can access live data without an issue. Is it possible the software isn't right?

Thanks for the help. I really appreciate your assistance with all of this :)

-Steve

[KyleAwesome]

Is your car OBDI or OBDII?


I don't know what you are talking about, cause I downloaded the file 5 sec ago, it works fine.


hmm, maybe the serer was doing maint, or they redirected load or something, I tried from two different IP's lastnight.

[stevek1490]

I was able to get the DME/ME module to respond, but I still can't get the DME to. I also haven't been able to pull live data from either module.

Does anyone have any suggestions? :(

[MaxVQ]

I was able to get the DME/ME module to respond, but I still can't get the DME to. I also haven't been able to pull live data from either module.

Does anyone have any suggestions? :(
I also can't get live data to work on my 01 530 and don't know why...

Is the DME and the DME/ME module the same? I will check and see what my carsoft shows later today and let you know...

[GEN3RIC]

ok Ill ask again. I read up some more and found that BMW Ultimate Pro 1.0 is out.. I haven't found anywhere to download a cracked version. I'm considering buying it because it looks like a decent update and includes Carsoft Information System 2.0 -- which actually thoroughly explains the codes.

Any thoughts?

[MaxVQ]

ok Ill ask again. I read up some more and found that BMW Ultimate Pro 1.0 is out.. I haven't found anywhere to download a cracked version. I'm considering buying it because it looks like a decent update and includes Carsoft Information System 2.0 -- which actually thoroughly explains the codes.

Any thoughts?

Do you realize the cost? When I looked into it in Feb 08 it was $3,600!!!

[GEN3RIC]

Do you realize the cost? When I looked into it in Feb 08 it was $3,600!!!
Let me redact my statement. Does anybody know of a cracked version? :rofl If I am gonna drop that much, I'll go out and get GT1.

[David Mc]

Sorry Eric,

If I knew where I could get a cracked version of Carsoft Ultimate Pro, I would also be running it. I am interested to see if you get a response on this one.

[upallnight]

Hey got my Carsoft program running tonight, thanks David Mc.

However, most of my Modules are not responding. Car is a 1993 525IT with the M50 Vanos engine. ANything I should look at as to why the modules are not responding?

If I got an earlier version of carsoft will it be a better fit for my e34?

[GEN3RIC]

If they don't respond, they probably don't exist.. which is fine. The support is there for new models that have those modules. Don't worry if they don't respond unless its DME ;)

[upallnight]

Changed to an old pentium laptop that my kids don't use anymore, but it has a built in serial port. Installed Carsoft and I was able to reset the airbag light. Another BMW owner loan me his peake airbag reset tool, but it wouldn't reset the module, but car soft gave me the fault and resetted the module. Now I don't need to see the SRS light on the dash anymore.

Woo Hoo

[GEN3RIC]

Til it comes on again. :tongue Usually a faulty sensor sets it off for no good reason too.

[upallnight]

The fault occurred during an extremely heavy down pour.

[Bimmermig]

I just got my interface, and cables (and am having to use a USB to Serial adapter because I don't have a notebook with a serial connection).

But it just errors, and says "Diagnostic Cable reports bad connection" Both the software and the computer are set for COM2. Any suggestions would be greatly appreciated.

hello Stevek
this is my first post here
i have exactly the same problem and the same diagnostic "bad connection"
from my compaq laptop,
no COM port so im using a serial/usb adaptor (dynex)
can you tell me please, how did you get it running?
i'd appreciate very much
my baby is a 2002 325i E46 sweet oxford green, inmaculate body perfect running (i think i'm in love)

Fern

[DJ Genius]

hello Stevek
this is my first post here
i have exactly the same problem and the same diagnostic "bad connection"
from my compaq laptop,
no COM port so im using a serial/usb adaptor (dynex)
can you tell me please, how did you get it running?
i'd appreciate very much
my baby is a 2002 325i E46 sweet oxford green, inmaculate body perfect running (i think i'm in love)

Fern
Usually it's because of a dodgy adapter, I have DELL Laptop and USB/serial adapter and it doesn't work, I also got PCMCIA card adapter, but have problems connecting it to laptop. The best thing is built in serial port, sad it's only on old laptops.

[stevek1490]

hello Stevek
this is my first post here
i have exactly the same problem and the same diagnostic "bad connection"
from my compaq laptop,
no COM port so im using a serial/usb adaptor (dynex)
can you tell me please, how did you get it running?
i'd appreciate very much
my baby is a 2002 325i E46 sweet oxford green, inmaculate body perfect running (i think i'm in love)

Fern

Exactly what DJ Genius said. I had a great deal of luck when I used XP instead of Vista, and then even better results using the built in COM port off a desktop that I dragged down into my garage.

I picked up a port replicator for an old IBM notebook I have, and am going to see if the COM port on the replicator works the same as having it built in (it should, its designed to do exactly that).

I still haven't been able to pull live data, but am going to try the OBD2 connector inside the car tonight to see if that is the reason.

Two things to keep in mind (based on what I've seen):

1 - Put the ignition in position 1 and try to read a module.
2 - If unable to read the module in position 1, try position 2

Some of my modules read from P1, some from P2.

[Ernbmw]

carsoft works fine,
The only problem I can’t read the fault code.

[JRW21]

if you do a single diagnosis it should give you the exact code. It won't give you the codes if you perform a total diagnosis.

[leoreyes69]

I try using serial to usb and it would give me a error message

[JRW21]

did you install the software for the usb cable?

[Ernbmw]

codes are in germen

[DJ Genius]

codes are in germen
Did you install the SP1?

[JRW21]

codes are in germen

try this: http://babelfish.yahoo.com/

[DJ Genius]

I know it happened to me when I was messing around with files, I got it only in German. I can't remember what I did, but I think I opened a wrong file. Did you notice you need to rename the file after all the installations? Just follow the exact steps David provided and you should be OK.

[Bimmermig]

did you install the software for the usb cable?

in my case, i did install the software that came with the adaptor i bought but it doesnt work
maybe there's a better one that would do the job?
id like very much to try that before moving my old desktop to my garage
thanks in advance
Fern

[hariskt]

Hello guys i would like to know something about carsoft...

My car is having obdii connection...bmw 318i e46 2002 model...4cyl..

I have a laptop intel core 2 without serial port (only 4 usb connections ) ....if i buy a carsoft cabel from ebay....is it possible to use...???

If so what are the required adapters should buy to use it.....????

Waiting for reply...thanks..

[320de46m47]

^^ I found that the serial port is essential ....had to switch laptops despite having bought a usb/serial adapter ...just didn't work

BTW Is it just me, or does anyone else find they are missing the Activation code with Carsoft? Or maybe it's just not necessary?

[David Mc]

Here is the info you need re the authentication code http://forums.bimmerforums.com/forum/showpost.php?p=13089394&postcount=110 . If you need the proper crack file, PM me, or alternatively download a working version of the software from here http://www.4shared.com/dir/7137899/6e9cd794/sharing.html and reinstall as per the instructions available on the same site.

[320de46m47]

when i uninstall old version and then reinstall as per instructions i get a message saying it cant complete due to being already on my pc ...?

[David Mc]

Did you follow this part of the insructions?

If you have EVER installed ANY version of Carsoft before:-

1. Uninstal the program using the ADD/DELETE Programs function available from the Control panel via SETTINGS on the START menu.

2. Use the Explore function to open the Programs tab from the START menu and delete any CARSOFT folders

3. Use the SEARCH function from the START menu to look for any files or folders containing the word CARSOFT and delete them.

4. Search your Hard Drive for a folder named CM70 or CM75s and use EXPLORE to view its contents. If you have located the correct folder it will contain CARSOFT files with names like "AIRBAG1.DXT" - DELETE THE ENTIRE FOLDER.

5. Restart your computer and from the START menu go to PROGRAMS then ACCESSORIES and select SYSTEM TOOLS then SYSTEM RESTORE and create a new restore point.

6. Once the new restore point has been created, close out of the SYSTEM RESTORE Menu, then go back into ACCESSORIES via the START and PROGRAMS Menus and choose SYSTEM TOOLS then DISK CLEANUP. Select the MORE OPTIONS Tab and under “System Restore,” choose to Delete all but the most recent RESTORE Point and run the Disk Cleanup utility.

7. Open the “My Computer” Icon on the Desktop and right click on the Icon for your Hard Drive, then click “Properties”. Click on the “Tools” Tab when the Properties Dialogue Box opens and choose “Check now”. Two Dialogue boxes will appear asking if you want to check & repair files and scan the hard drive. Check both boxes then the START button. A message will appear telling you that this process can only be performed when the computer re-starts and asking you to confirm whether you wish this to occur. Confirm this request, then restart your computer. Dependent upon how many files you have stored and the size of the Hard Drive, the scanning process may take 2 -3 hours to complete after the system is restarted.

It sounds as if there is still a resident file or entry on your computer or in its registry.

[belligerent]

First off thanks DAvid for the instructions and links !!!!
awesome stuff


it seems to all have worked for me ....


except the activation code part ..... the box pops up and I cant enter the code , but when i close the box Carsoft seems to work .....


Does this sound like its working properly????

[320de46m47]

id assumed the activation code informs carsoft that you bought it (which we didnt!) and gives updates ...but it seems to work ok without it.. so (or does it?) ?

[David Mc]

The activation code actually enables the software to run but if you are able to run diagnostics and access live data all is OK as the cracks are actually just a workaround to avoid the requirement to enter an activation code.

[320de46m47]

I bought a carsoft 6.5 cdrom off ebay some months ago .. same issue with that. it only works if i open from the cd and not install it onto the pc ( in this event it doesn't work) ... it runs seemingly normally if i click on one icon (the one with 6.5 written in it) in the list however if i click on the blueish laptop pic icon it asks for the activation code and will only take me to screens showing the hardware in photos company HQ etc. presumably the one i bought off ebay is cracked also despite the fact that it has no activation /update code. what screen do you get if you enter an activation /update code? it's really just a question of not knowing what happens (if anything) with theis activation code.

[David Mc]

The actual Carsoft program is the one activated by the CS v6.5 icon. The Blue Laptop is only a file which is why when you open it all you see are the help screens and the activation code prompt. When the software is cracked properly and installed the Blue laptop file is actually replaced with one that contains only the help files and no activation code request. Entry of the activation code in the original software only removes a stop which would normally only permit the program to open upon entry of the proper code (as it does when cracked, but without the requirement for code entry).

[320de46m47]

ok so there is no problem ...thanks for going to all the trouble of explaining

[SnailTail]

Hello,

I don't mean to re-ask the same question, but I have now read the entire thread twice and can't seem to find a solid answer before I buy carsoft on ebay. Will carsoft allow me to get live data from my 1994 318is (e36) with an OBD I?

-Adam.

[DJ Genius]

Hello,

I don't mean to re-ask the same question, but I have now read the entire thread twice and can't seem to find a solid answer before I buy carsoft on ebay. Will carsoft allow me to get live data from my 1994 318is (e36) with an OBD I?

-Adam.
No, you won't get LIVE DATA from OBDI car, only from OBDII cars :)
Just to get an idea what you're getting when buying Carsoft v6.5, read my thread (in the sig).

[SnailTail]

Thanks a lot for your quick reply.

Carsoft seems like the best program and I will probably end up getting it. Darn, I just wish there was a way to get live data from my obd I. Are there any programs other than carsoft that can get me live data - it is one of the main functions I am looking for.
-Adam.

[DJ Genius]

Thanks a lot for your quick reply.

Carsoft seems like the best program and I will probably end up getting it. Darn, I just wish there was a way to get live data from my obd I. Are there any programs other than carsoft that can get me live data - it is one of the main functions I am looking for.
-Adam.
Not really, because that's why there was OBDII invented:) The biggest update on OBDII was availability to get LIVE DATA + other useful modules.

[mike972]

rrosscoe,

The carsoft_bmw65_crack folder should contain 10 files, yours contains only 4. Email me.

david my crack files dir counts 4 so can you mail me the right crack ?

[DJ Genius]

As David mentioned COUPLE of times on this thread, you can download EVERYTHING you need from here (the CRACK is included in the RAR file):
http://www.4shared.com/dir/7137899/6e9cd794/sharing.html

[mike972]

As David mentioned COUPLE of times on this thread, you can download EVERYTHING you need from here (the CRACK is included in the RAR file):



Thanks i'll try this and hope it works for me

[mike972]

can read the dme but i can't get live data on my e46 320i 98
and when i try to get data from the ews unit i get a blue screen.

[lewy1124]

hi david iv been having a nightmare with carsoft but i read your page last night and tried it gets allot further than before but it says module not responding ive checked my crack folder and there are 10 files ive got an e46 year 2000 it has two diag ports ive tried the obd one in the footwell of car reading some more pages i noticed that someone had trouble with there interface saying all the green lights except the service were on mine is the same is this normall any help at all would be greatly appreciated thanks,craig

[David Mc]

It you are using the OBD2 port under the dash, you must make sure that the cap is on the 20 pin BMW diagnostic connector under the hood. The cap is fitted with jumpers that connect pins in the diagnostic port when it is in place and if it is not, you will not be able to access all the info via the OBD2 port. It is normal for all lights but the service light to be on when you are connected. Try this link for a few general Carsoft troubleshooting tips http://www.4shared.com/file/55507561/a1ae5f47/Carsoft_Trouble_Shooting_Tips.html

[lewy1124]

david you really are the carsoft man finally its up and runnig just got to learn how to use now do you know where i can get a user guide

[DJ Genius]

david you really are the carsoft man finally its up and runnig just got to learn how to use now do you know where i can get a user guide
You can always read my review thread (in the signature), that would be a nice start :)

[charger758]

When I install the setup.exe file, I get an error towards the end of the installation it looks like this.
http://img71.imageshack.us/img71/3302/carsofterrorga7.jpg

[DJ Genius]

When I install the setup.exe file, I get an error towards the end of the installation it looks like this.
http://img71.imageshack.us/img71/3302/carsofterrorga7.jpg
What is the location folder of the setup.exe file and what is the location you're installing it?

[charger758]

C:\Documents and Settings\Josh\Desktop\Carsoft\BMW CARSOFT 6.5\BMW

C:\Program Files\CARSOFT\BMW

[DJ Genius]

OK, try to move all installation files to location C:\ and then try installing it.

[charger758]

You guys are great, I had the problem with my desktop. I tried on my laptop at work from the C: drive and the program is up and running. I ordered my cable, so we'll see how things go from there.

Has anyone actually been able to do a EWS align (sync) with Carsoft?

[airbone]

Hello guys,
I am having troubles to force the CARSOFT 6.5 run. I bought interface from german ebay, but no success to make it work. When I start any scan (either complete test or picking up any of modules), I get the same result - after progress meter gets half-way, program falls down and closes with standard windows error message (carsoft encountered problem... send/don't send blah blah...) I have tried different copies of CS6.5 and also this that's link is posted in this thread (also with service pack1 installed), but still same outcome. I have also tried old CS 6.1 - alike a CS6.5, programm does not exit, but I get only "does not response" on every module. I tried with my laptop DELL with real COM port and also with duty laptop AVERATEC with USB to COM adapter - both systems with XP SP2 - same outcome. Testing car is E39 530d 2002. Tomorow gonna try on my friend's E46 318i 1999 with old 20pin socket, but I have strange feeling it will end up the same. Any idea what might be wrong??? Thanks in advance for any tips how to start sorting it out.